| www.deadharddrive.com Deadharddrive forum
|
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in| Search found 12 matches |
| Author | Message |
|---|---|
 Topic: Have you successfully recovered a dead hard drive? |
|
| marceljack Replies: 4 Views: 16355 |
 Forum: General chat Posted: Tue May 23, 2006 9:08 pm Subject: Re: Have you successfully recovered a dead hard drive? |
| And how did you do it?Maxtor Diamondmax Plus 9 (motor control IC burnt) : I swapped board from another disk of the same series with same hardware but different firmware. So I had also to remove the sm ... | |
| Topic: 6E040L0 DEFECTIVE |
|
| marceljack Replies: 2 Views: 10649 |
Forum: More stories Posted: Tue May 23, 2006 7:49 pm Subject: Re: 6E040L0 DEFECTIVE |
| All 6E040L0 hard drives are defective so don't use them and if you have one that works, replace it immediately no matter what!
I would personally like to watch (from a distance) a nuclear bomb dest ... |
|
| Topic: need board for DiamondMax Plus 9 6Y060L0420401 |
|
| marceljack Replies: 2 Views: 11619 |
Forum: Hard drives wanted Posted: Mon May 22, 2006 7:22 pm Subject: board |
| www.softcom.com.my
Try here...  :shock:Thanks. I solved mu problem with the help of Ranikolahdd. |
|
| Topic: Compatibility rules for replacing boards on Maxtor HDDs |
|
| marceljack Replies: 9 Views: 28487 |
Forum: Hard drives wanted Posted: Sun May 21, 2006 2:56 pm Subject: Re: re Flash |
| no it does not contain bad sector information and it is needed only for starting the hdd it has a small part of firmware not assential
there si a whay to read it I assume that there is a way to read ... |
|
| Topic: Compatibility rules for replacing boards on Maxtor HDDs |
|
| marceljack Replies: 9 Views: 28487 |
Forum: Hard drives wanted Posted: Sat May 20, 2006 3:38 pm Subject: Thanks |
| OK d2XXXX OR D6 XXXXXThanks, it's clear now.
put little rom chip from d2xxx on e4xxx board and the magic will startThanks, I will give it a try... I see in the ST documentation that this chip (mar ... |
|
| Topic: Compatibility rules for replacing boards on Maxtor HDDs |
|
| marceljack Replies: 9 Views: 28487 |
Forum: Hard drives wanted Posted: Fri May 19, 2006 9:58 pm Subject: Re: re |
| i am an expert in that field, maxtors are mine favorites.Okay.
U can use F4FYa on all BWo models and D2 or D6 boards on Vwo. End of storyThe disk with dead board has Code YAR41VW0 and its board is m ... |
|
| Topic: Wanted: Maxtor DiamondMax Plus 9 board w/ YAR41VW0 firmware |
|
| marceljack Replies: 7 Views: 23964 |
Forum: Hard drives wanted Posted: Fri May 19, 2006 9:07 pm Subject: Firmware |
| Does the firmware version have to match exactly?
Apparently there are 2 different firmwares for the 60GB/platter drives: YAR41VW0 and YAR41BV0. Can I use a controller board with YAR41BV0 on my drive ... |
|
| Topic: Compatibility rules for replacing boards on Maxtor HDDs |
|
| marceljack Replies: 9 Views: 28487 |
Forum: Hard drives wanted Posted: Fri May 19, 2006 7:12 pm Subject: Re: not good |
| this is not right
it is much easer there are onlye few board for eachmodel (speaking with maxtors) for qvantum it is even ease only as has 2 alll the others are the sameThis is the answer given in ... |
|
| Topic: Maxtor Diamondmax 16 60gb circuit board needed badly. |
|
| marceljack Replies: 4 Views: 16005 |
Forum: Hard drives wanted Posted: Tue May 16, 2006 8:04 pm Subject: Re: firmware code is RAMC1TU0 |
| The firmware code is RAMC1TU0. Thanks for letting me know what I need to supply. I'm new at this dead drive stuff. Thanks again.This is the compatibility rule that Maxtor support indicated me when ... | |
| Topic: Worked for Maxtor DiamondMax Plus 9 120GB |
|
| marceljack Replies: 5 Views: 19213 |
Forum: More stories Posted: Tue May 16, 2006 7:55 pm Subject: Re: Worked for Maxtor DiamondMax Plus 9 120GB |
| Searched internet for firmware code (see below), took a few weeks, but found someone with a dead platter.
$20 USD for shipping & handling (he didn't charge for the dead drive itself) and an ext ... |
|
| Topic: Compatibility rules for replacing boards on Maxtor HDDs |
|
| marceljack Replies: 9 Views: 28487 |
Forum: Hard drives wanted Posted: Tue May 16, 2006 7:41 pm Subject: Compatibility rules for replacing boards on Maxtor HDDs |
| Please find below the compatibility rules to follow to replace a damaged board on a Maxtor drive with a board coming from another drive of the same series.
To replace the circuit board on all Quant ... |
|
| Topic: need board for DiamondMax Plus 9 6Y060L0420401 |
|
| marceljack Replies: 2 Views: 11619 |
Forum: Hard drives wanted Posted: Tue May 16, 2006 7:35 pm Subject: need board for DiamondMax Plus 9 6Y060L0420401 |
| I need to replace the board of my 60GB drive (motor control chip burnt, which seems very frequent).
According to Maxtor support, the replacement board does not need to come from a disk with the same ... |
|
All times are GMT |
Powered by phpBB © 2001, 2005 phpBB Group