www.deadharddrive.com
Deadharddrive forum
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Search found 37 matches
www.deadharddrive.com Forum Index
Author Message
  Topic: Seagate Barracuda 7200.10 500GB
tester272001

Replies: 0
Views: 12817

PostForum: Hard drives available   Posted: Mon Sep 19, 2016 1:00 am   Subject: Seagate Barracuda 7200.10 500GB
In case anyone needs the PCB:

ST3500630AS
P/N: 9BJ146-305
Firmware: 3.AAE
Date Code: 07484 Site code: TK (product of Tailand)

The PCB works but the drive is toast.
  Topic: Seagate ST31000528AS, - looking for some tips
tester272001

Replies: 6
Views: 27573

PostForum: General chat   Posted: Fri Nov 16, 2012 11:47 pm   Subject: Seagate ST31000528AS, - looking for some tips
Sooo. Is this what a preamp failure sounds like? The linked sound file is an MP3 and has 10 clicks then stops but the drive continues to SPIN. If I unplug/replug it does aga for 10 and stop, etc...
  Topic: Seagate ST31000528AS, - looking for some tips
tester272001

Replies: 6
Views: 27573

PostForum: General chat   Posted: Fri Nov 16, 2012 3:34 am   Subject: Seagate ST31000528AS, - looking for some tips
Here is a link to the sound this drive is making:
http://picosong.com/3k35/
Can you tell if this is a fried HDA coil or the PCB ????
  Topic: Another Maxtor OneTouch II that Won't Boot (Pics)
tester272001

Replies: 1
Views: 13098

PostForum: General chat   Posted: Tue Nov 13, 2012 11:35 pm   Subject: Another Maxtor OneTouch II that Won't Boot (Pics)
Get an Ohm meter and check the forward/reverse readings n the BIG BUX diode right below the CR200 label. If it reads zero Ohm in both directions its fried (even if it does not look fried). If it rea ...
  Topic: Seagate ST31000528AS, - looking for some tips
tester272001

Replies: 6
Views: 27573

PostForum: General chat   Posted: Tue Nov 13, 2012 11:32 pm   Subject: Seagate ST31000528AS, - looking for some tips
Client with post hurricane Sandy/power failure. firmware CC35 date mfg 09446. PCB is 100536501 REV A. This units PCB had a shorted 12V TVS diode and two zero Ohm resistors from the molex to the TVS. ...
  Topic: Dead Maxtor DiamondMax9
tester272001

Replies: 7
Views: 28111

PostForum: General chat   Posted: Thu Dec 29, 2011 12:30 am   Subject: Dead Maxtor DiamondMax9
I am attempting a PCB swap but the K4FYA board when swapped with a L6FYA did not work (they look identical and all chips match). So based on other information I found it seems that the 6Y120P0 032251 ...
  Topic: Dead Maxtor DiamondMax9
tester272001

Replies: 7
Views: 28111

PostForum: General chat   Posted: Sun Dec 25, 2011 6:50 pm   Subject: Dead Maxtor DiamondMax9
When looking for a match of the Diamond Plus 9 does the LBA have to match exactly? this is a 6Y120P0 unit...
  Topic: SOLDERING TIPS,
tester272001

Replies: 1
Views: 13956

PostForum: More stories   Posted: Sun Oct 16, 2011 5:26 pm   Subject: solder iron
I presume you do not want the station is was designed to work with?
http://www.amazon.com/Hakko-Soldering-Station-FX-888/dp/B004M3U0VU
It is only $83USD not bad for tem controlled. What exactly are ...
  Topic: Some help for Maxtor DiamonMax Plus 9 120GB ATA/133 HDD
tester272001

Replies: 23
Views: 54279

PostForum: More stories   Posted: Mon May 10, 2010 12:55 am   Subject: Some help for Maxtor DiamonMax Plus 9 120GB ATA/133 HDD
OK so the drive spinds and clicks. The preamp is presumably GOOD? Is my problem then perhaps the firmware is just not exactly for the drive I have vs. the PCB I bought ?
  Topic: Some help for Maxtor DiamonMax Plus 9 120GB ATA/133 HDD
tester272001

Replies: 23
Views: 54279

PostForum: More stories   Posted: Mon May 10, 2010 12:47 am   Subject: Some help for Maxtor DiamonMax Plus 9 120GB ATA/133 HDD
Thanks once again for a lead. In my original post I said, the original pcb was a K4FYA. I replaced with PCB L6FYA. Would the two digit number in the front portion of that make a significant differe ...
  Topic: Some help for Maxtor DiamonMax Plus 9 120GB ATA/133 HDD
tester272001

Replies: 23
Views: 54279

PostForum: More stories   Posted: Sun May 09, 2010 2:22 am   Subject: Some help for Maxtor DiamonMax Plus 9 120GB ATA/133 HDD
The saga continues. I transferred the 503 chip from the doner board to the old PCB and the voltages look good. The HDD does not spin up. I measured zero volts on all of the four pins that feed the ...
  Topic: Some help for Maxtor DiamonMax Plus 9 120GB ATA/133 HDD
tester272001

Replies: 23
Views: 54279

PostForum: More stories   Posted: Fri May 07, 2010 11:54 pm   Subject: Some help for Maxtor DiamonMax Plus 9 120GB ATA/133 HDD
Well I checked some voltages on the known good board and the IC that is fried normally carries 5V+/- and the TVR diode on the other side is measuring +12V. So the 5volt line shorted in the FW503 chip. ...
  Topic: Some help for Maxtor DiamonMax Plus 9 120GB ATA/133 HDD
tester272001

Replies: 23
Views: 54279

PostForum: More stories   Posted: Fri May 07, 2010 5:05 am   Subject: Some help for Maxtor DiamonMax Plus 9 120GB ATA/133 HDD
fzabkar, hopefully sunndreamspace was just joking with you and not being nasty. I will say that its great to have someone try to help. I have helped many people ove the net with lots of problems and ...
  Topic: Some help for Maxtor DiamonMax Plus 9 120GB ATA/133 HDD
tester272001

Replies: 23
Views: 54279

PostForum: More stories   Posted: Fri May 07, 2010 4:59 am   Subject: Some help for Maxtor DiamonMax Plus 9 120GB ATA/133 HDD
BTW - I scraped the top of that FW503 and it had burned carbon! I check the one on the new board and it was fine. You may have nailed that DC to DC converter! According to the datasheet it has an i ...
  Topic: Some help for Maxtor DiamonMax Plus 9 120GB ATA/133 HDD
tester272001

Replies: 23
Views: 54279

PostForum: More stories   Posted: Fri May 07, 2010 4:47 am   Subject: Some help for Maxtor DiamonMax Plus 9 120GB ATA/133 HDD
Thanks for the replies. I checked the TVS diode you identified and it looks good. On 200 Ohm scale its open. But if I use the diode check setting it has low/high reading as expected. I checked on ...
 
Page 1 of 3 Goto page 1, 2, 3  Next
All times are GMT
Jump to:  


www.deadharddrive.com latest topics RSS feed 
Powered by phpBB © 2001, 2005 phpBB Group