www.deadharddrive.com
Deadharddrive forum
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

WD3200JB crash

 
Post new topic   Reply to topic    www.deadharddrive.com Forum Index -> General chat
View previous topic :: View next topic  
Author Message
wizzy1
Officially active!


Joined: 04 Nov 2009
Posts: 4
Location: Illinois

PostPosted: Wed Nov 04, 2009 3:15 pm    Post subject: WD3200JB crash Reply with quote

Hi all,
I have a WD caviar SE IDE drive connected by firewire via a iomega ion drive enclosure to my Mac Mini OSX 10.4.11. The drive has made funny noises in the past which I corrected by turning off/on the enclosure. Two weeks ago the drive was discovered dead. not recognized, no vibration no noise. I removed the drive and stuck it in a linux computer. No noise no vibration not recognized or seen. I put an old hitachi 4GB drive in the enclosure. It spun up nicely and was recognized by the Mac. So I know the enclosure works.
This is my drive.
P/N WD3200JB-OOKFAO
Date: 10 JAN 2006
DCM: DSBACAJCH
on the PCB 2060 701314002 Rev A
on whte sticker above IDE 2061-701314-AOO-AG
Green V1 sticker above jumpers
5BF2 light writing next to V1 sticker
some black corrosion in a few pins on motor controller chip

A friend had the exact same model drive sitting in a drawer at home.
same p/n
date 06 FEB 2006
DCM HSCACAJCA
Both drives made in Thailand
White sticker 2061-701314-AOO-AG
So I swapped out the PCBs and placed the drive in the enclosure and the drive spins! But it is not reconized by the mac or the linux box. I ran testdrive on the drive and it says it is only 18 or 19 GB I have not run photorec yet. There is another drive for sale on ebay with this white sticker no. 2061-701314-A00 AA .
I'm going to try to remove the black crud around the motor controller chip see if that works. if not my optins are swap the U12 chip or buy the other drive and swap those PCB's. I'm a little leary of soldering.
whicch should I do?
wizzy1
Back to top
View user's profile Send private message
wizzy1
Officially active!


Joined: 04 Nov 2009
Posts: 4
Location: Illinois

PostPosted: Wed Nov 04, 2009 6:14 pm    Post subject: also Reply with quote

photorec is a part of the open software testdrive. It can pull fotos and songs off of drives. thats all I want off this thing any way. So should try the software solution, instead.
Back to top
View user's profile Send private message
harddrivespecialist
Deadharddrive regular +4


Joined: 29 Dec 2007
Posts: 471
Location: Providence, RI. Boston, MA USA

PostPosted: Thu Nov 05, 2009 12:38 am    Post subject: Reply with quote

Software won't help you resolve your issue.
You have to swap ROM chip in order to match original drive microcode.
_________________
www.datarecoveryne.com
Back to top
View user's profile Send private message Visit poster's website
sunnydreamspace
Deadharddrive regular +5


Joined: 04 Jan 2009
Posts: 540

PostPosted: Thu Nov 05, 2009 2:59 pm    Post subject: Reply with quote

hi,
you had to swap ROM chip for try. U12 8 pin one. you can contact me by email if still no work. thanks.
_________________
provide Hard drive PCB,entire drive/ Data Recovery service.... big HDD resource. talk to me immediately! sunnydreamspace@hotmail.com
skype: sunnydreamspace
Back to top
View user's profile Send private message Visit poster's website AIM Address Yahoo Messenger MSN Messenger
wizzy1
Officially active!


Joined: 04 Nov 2009
Posts: 4
Location: Illinois

PostPosted: Sat Nov 07, 2009 2:11 am    Post subject: Sucess!!! Reply with quote

well,
I decided to do the ROM swap. I have never desoldered or even soldered an IC chip before.I praticed desoldering many times on old ISA boards I had lying around and screwed it up every time. So I broke down and ordered some CHIP QUIK. I tried desoldering and got it the first try. So off I went to do the real thing. It was nerve racking. When I finished the swap, I placed the board back in the damaged drive. Placed the drive back in the external enclosure and pluged it into my Mac and Voilla!! The mac recognized it in 10 sec. I am now transfering my data to a new drive and will probally throw the old drive away. So it can be done and I thank everyone on this board, because without the U12 info I would have been out vaulable data.
thanks
wizzy1
Back to top
View user's profile Send private message
wizzy1
Officially active!


Joined: 04 Nov 2009
Posts: 4
Location: Illinois

PostPosted: Sat Nov 07, 2009 2:12 am    Post subject: Reply with quote

BTW removing the black crud did nothing that board was hosed
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    www.deadharddrive.com Forum Index -> General chat All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


www.deadharddrive.com topic RSS feed 
Powered by phpBB © 2001, 2005 phpBB Group